 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ZL40167 High Output Current High Speed Dual Operational Amplifier Data Sheet Features * High Output Drive * * * * * * * 18.8 Vpp differential output voltage, RL = 50 9.4 Vpp single-ended output voltage, RL = 25 200mA @ Vo = 9.4 Vpp, Vs = 12V * * High ESD (Electro-Static Discharge) immunity * * 4kV for Supply and Output pins 0.005% and -0.07deg Low differential gain and phase 85dB SFDR (Spurious Free Dynamic Range) @ 100KHz, Vo = 2Vpp, RL = 25 192MHz 3dB bandwidth (G=2) 240V / s slew rate 3.8nV / Hz: input noise voltage 2.7pA / Hz: input noise current Single-supply operation: 5V to 12V ZL40167/DCA (tubes) 8 lead SOIC ZL40167/DCB (tape and reel) 8 lead SOIC -40C to +85C September 2003 Ordering Information High Output Current Low Distortion High Speed * * Applications * * * ADSL PCI modem cards xDSL external modem Line Driver * Low Noise * * * Low supply current: 7mA/amp * Out_1 1 8 V+ 7 Out_2 1 6 In_n_2 2 ZL40167 5 In_p_2 In_n_1 2 In_p_1 3 V- 4 Figure 1 - Functional Block Diagram and Pin Connection 1 Zarlink Semiconductor Inc. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved. ZL40167 Description Data Sheet The ZL40167 is a low cost voltage feedback opamp capable of driving signals to within 1V of the power supply rails. It features low noise and low distortion accompanied by a high output current which makes it ideally suited for the application as an xDSL line driver. The dual opamp can be connected as a differential line driver delivering signals up to 18.8Vpp swing into a 25 load, fully supporting the peak upstream power levels for upstream full-rate ADSL (Asymmetrical Digital Subscriber Line). The wide bandwidth, high power output and low differential gain and phase figures make the ZL40167 ideally suited for a wide variety of video driver applications. Application Notes The ZL40167 is a high speed, high output current, dual operational amplifier with a high slew rate and low distortion. The device uses conventional voltage feedback for ease of use and more flexibility. These characteristics make the ZL40167 ideal for applications where driving low impedances of 25 to 100 such as xDSL and active filters. The figure below shows a typical ADSL application utilising a 1:2 transformer, the feedback path provides a Gain = +2. 12R5 Rf1 Rg Rf2 100R 12R5 Figure 2 - A Typical ADSL Application A class AB output stage allows the ZL40167 to deliver high currents to low impedance loads with low distortion while consuming low quiescent current. Note: the high ESD immunity figure of 4kV may mean that in some designs fewer additional EMC protection components are needed thus reducing total system costs. The ZL40167 is not limited to ADSL applications and can be used as a general purpose opamp configured with either inverting or non-inverting feedback. The figure below shows non-inverting feedback arrangement that has typically been used to obtain the data sheet specifications. 2 Zarlink Semiconductor Inc. ZL40167 Data Sheet Rf Rg Figure 3 - A Non-Inverting Feedback Amplifier Example Video transmitter and receiver for twisted wire pair Composite video signals can be transmitted down twisted pair cable, i.e. Ethernet (CAT 5), using a differential transmitter and receiver. The transmitter must be able to drive high currents into the low impedance twisted pair cable. For video, the amplifiers require flat gain and low phase-shift over the video signal band. To ensure this, the amplifiers will have 3dB bandwidths well in excess of this. The ZL40167 (dual amplifier) has all of these attributes. With reference to the differential video driver shown in Figure , the input coax is assumed to have a characteristic impedance of 75 Ohms, this is terminated with a parallel combination of 110 Ohms and the input impedance of amplifier IC1 (b) of 255 Ohms, giving 77 Ohms. Low values of feedback resistors are used around the op-amps to reduce phase-shift due to parasitic capacitors and to minimise the addition of noise. Baseband PAL or NTSC video signals generally have an amplitude of 2V pk-pk. A gain of two is used to ensure that the signal level at the end of the (terminated with 100 Ohms) differential pair will be the same as the input level, neglecting any losses due to the use of long cable lengths. Composite Video Co-Ax Input IC1(a) 50R 110R 510R 510R 50R 510R IC1(b) 510R 510R Twisted Pair Output Figure 4 - Differential Video Driver The differential receiver is shown in Figure 5 has a 100 Ohm line termination resistor, followed by a differential amplifier. Long cables will tend to attenuate the signal with greater losses at the higher frequencies, so the second amplifier is used to equalise these losses. Initially the amplifier should be built without fitting components R1 and 3 Zarlink Semiconductor Inc. ZL40167 Data Sheet C1. Select the value of R2 to give the required gain at low frequency. Adjust the values of R1 and C1 to correct for the frequency dependant attenuation of the cable. To drive a coax cable the output of the amplifier is connected via a series matching 75 Ohm resistor, again this second (dual amplifier) ZL40167 provides the required power output for the restored 2Vpk-pk video signal. 510R 510R Twisted Pair Input 100R 510R 510R IC2(a) R2 C1 R1 IC2(b) 510R 75R Composite Video Co-Ax Output Figure 5 - Differential Video Receiver 4 Zarlink Semiconductor Inc. ZL40167 Absolute Maximum Ratings - (See Note 1) Parameter Vin Differential Output Short Circuit Protection Symbol VIN VOS/C Min Max 1.2 See Apps Note in this data sheet 13.2 (V-) -0.8 (V+) +0.8 5.5 4 -55 +/-100mA for 100ms 20% pulse for 100ms (Note 3) +150 (Note 4) (Note 5) Data Sheet Units V Supply Voltage Voltage at Input Pins Voltage at Output Pins ESD Protection (HBM Human Body Model) (See Note 2) Storage Temperature Latch-up test Supply transient test Note 1: Note 2: Note 3: Note 4: Note 5: V+, VV(+IN), V(-IN) VO V V V kV C Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Human body model, 1.5k in series with 100pF. Machine model, 200 in series with 100pF. 1.25kV between the pairs of +INA, -INA and +INB, -INB pins only. 4kV between supply pins, OUTA or OUTB pins and any input pin. +/-100mA applied to input and output pins to force the device to go into "latch-up". The device passes this test to JEDEC spec 17. Positive and Negative supply transient testing increases the supplies by 20% for 100ms. Operating Ratings - (See Note 1) Parameter Supply Voltage Junction Temperature Range Junction to Ambient Resistance Rth(j-a) Symbol V+, VMin 2.5 -40 150 Max 6.5 150 Units V C C 4 layer FR5 board C 4 layer FR5 board Junction to Case Resistance Rth(j-c) 60 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. 5 Zarlink Semiconductor Inc. ZL40167 otherwise specified. Min (Note 1) Typ (Note 2) Max (Note 3) Data Sheet Electrical Characteristics - TA = 25C, G = +2, Vs = 6V, Rf = Rg = 510, RL = 100 / 2pF; Unless Symbol Parameter Conditions Units Test Type Dynamic Performance -3dB Bandwidth -0.1dB Bandwidth Slew Rate Rise and Fall Time Rise and Fall Time Differential Gain Differential Phase 2nd Harmonic Distortion Vo = 200mVp-p Vo = 200mVp-p 4V Step O/P, 10-90% 4V Step O/P, 10-90% 200mV Step O/P, 10-90% NTSC, RL = 150 NTSC, RL = 150 192 32 240 13.3 1.7 0.005 -0.07 MHz MHz V/s ns ns % deg C C C C C C C Distortion and Noise Response Vo = 8.4Vpp, f =100KHz,RL= 25/2pF Vo = 8.4Vpp, f =1MHz,RL = 100/2pF Vo = 2Vpp, f =100kHz,RL= 25/2pF Vo = 2Vpp, f =1MHz,RL =100/2pF 3rd Harmonic Distortion Vo = 8.4Vpp, f =100KHz,RL=25/2pF Vo = 8.4Vpp, f =1MHz,RL =100/2pF Vo = 2Vpp, f =100KHz,RL=25/2pF Vo = 2Vpp, f =1MHz,RL=100/2pF MTPR Multi-Tone Power Ratio 47.4375 KHz 69 KHz 90.5625 KHz 112.125 KHz Input Noise Voltage Input Noise Current f = 100KHz f = 100KHz -65.4 -83.8 -93.6 -86 -70 -77.7 -85 -73.5 -75 -76.3 -73.8 -71.5 3.85 2.7 dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc nV/Hz pA/Hz C C C C C C C C C C C C C C 6 Zarlink Semiconductor Inc. ZL40167 Symbol Parameter Conditions Min (Note 1) Typ (Note 2) Max (Note 3) Data Sheet Units Test Type Input Characteristics Vos Ib Ios CMVR CMRR Input Offset Voltage Input Bias Current Input Offset Current Common Mode Voltage Range Common Mode Rejection Ratio Voltage Gain Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C -2 - 4.9 70 79 - 4.2 - 0.3 -10 -0.2 4.2 -20 2 4.9 mV A A V dB A A A A A Transfer Characteristics Avol RL = 1k, Tj = -40C to 150C RL = 25, Tj = -40C to 150C Output Swing Output Swing Isc Output Current (Note 3) Supply Current / Amp Power Supply Rejection Ratio RL = 25, Tj = -40C to 150C RL = 1k, Tj = -40C to 150C Vo = 0, Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C 73 4.7 1.6 - 4.5 -5 570 10 5.5 4.7 5.1 1000 4.5 5 V V mA V/mV A A A A B Power Supply Is PSRR 7 81 9 mA dB A A Note 1: Note 2: The maximum power dissipation is a function of Tj(max), JA and TA. The maximum allowable power dissipation at any ambient temperature is PD = (Tj(max) - TA)/ JA. All numbers apply for packages soldered directly onto a PC board. Typical values represent the most likely parametric norm. Note 3: Test Types: a. 100% tested at 25C. Over temperature limits are set by characterisation, simulation and statistical analysis. b. Limits set by characterisation, simulation and statistical analysis. c. Typical value only for information. 7 Zarlink Semiconductor Inc. ZL40167 Data Sheet 2.5V Electrical Characteristics - TA = 25C, G = +2, Vs = 2.5V, Rf = Rg = 510, RL = 100 / 2pF; Unless otherwise specified. Symbol Parameter Conditions Min (Note 1) Typ (Note 2) Max (Note 3) Units Test Type Dynamic Performance -3dB Bandwidth -0.1dB Bandwidth Slew Rate Rise and Fall Time Rise and Fall Time Distortion and Noise Response 2nd Harmonic Distortion Vo = 2Vpp,f = 100KHz, RL = 25 Vo = 2Vpp, f = 1MHz, RL = 100 3rd Harmonic Distortion Vo = 2Vpp, f = 100KHz, RL = 25 Vo = 2Vpp, f = 1MHz, RL = 100 Input Characteristics Vos Ib CMVR CMRR Input Offset Voltage Input Bias Current Common Mode Voltage Range Common Mode Rejection Ratio Tj = -40C to 150C Tj = -40C to 150C Tj = -40C to 150C -1.55 70 80 - 4.2 - 0.3 - 10 4.2 -20 1.55 mV A V dB B B B B -92.6 -85 -86.3 -74.8 dBc dBc dBc dBc C C C C 1V Step O/P, 10-90% 1V Step O/P, 10-90% 200mV Step O/P, 10-90% 176.5 83.8 216 3.7 1.7 MHz MHz V/s ns ns C C C C C Transfer Characteristics Avol Voltage Gain RL = 1k, Tj = -40C to 150C RL = 25, Tj = -40C to 150C Output Characteristics Output Swing RL = 25, Tj = -40C to 150C RL = 1k, Tj = -40C to 150C -1.4 -1.6 1.45 1.65 1.4 1.6 V B B 5.5 1.6 10.5 5.8 V/mV B B 8 Zarlink Semiconductor Inc. ZL40167 Symbol Power Supply Is PSRR Note 1: Note 2: Data Sheet Typ (Note 2) Max (Note 3) Test Type Parameter Conditions Min (Note 1) Units Supply Current/Amp Power Supply Rejection Ratio Tj = -40C to 150C Tj = -40C to 150C 73 6.75 83 8.5 mA dB A B The maximum power dissipation is a function of Tj(max), JA and TA. The maximum allowable power dissipation at any ambient temperature is PD = (Tj(max) - TA)/ JA. All numbers apply for packages soldered directly onto a PC board. Typical values represent the most likely parametric norm. Note 3: Test Types: a. 100% tested at 25C. Over temperature limits are set by characterisation, simulation and statistical analysis. b. Limits set by characterisation, simulation and statistical analysis. c. Typical value only for information. 9 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100,Vs = 6V. Unless otherwise specified. Output Sw ing 12.0 10.0 Vout Swing (V) 8.0 R L = 1K 6.0 4.0 RL = 25 2.0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 +/- Supply (V) Figure 6 - Output Swing Positive Output Sw ing into 1Kohm s 1.0 0.9 0.8 0.7 0.6 85 C 0.5 0.4 0.3 0.2 0.1 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 - 40 C 25 C Vsupply - Vout (V) +/- Supply (V) Figure 7 - Positive Output Swing into 1K 10 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Negative Output Sw ing into 1Kohm s 1.0 0.9 0.8 25 C 85 C - 40 C Vout - Vsupply (V) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 +/- Supply (V) Figure 8 - Negative Output Swing into 1K Positive Output Sw ing into 25 ohm s 1.4 1.2 25 C 1.0 Vsupply - Vout (V) 0.8 85 C 0.6 0.4 0.2 0.0 1.0 2.0 3.0 4.0 +/- Supply (V) 5.0 6.0 7.0 -40 C Figure 9 - Positive Output Swing into 25 11 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Negative Output Sw ing into 25 ohm s 1.4 1.2 25 C 1.0 - 40 C Vout - Vsupply (V) 0.8 85 C 0.6 0.4 0.2 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 +/- Supply (V) Figure 10 - Negative Output Swing into 25 +Vout vs. ILoad 5.4 5.3 5.2 85 C 5.1 25 C 5.0 4.9 - 40 C 4.8 4.7 4.6 0.00 0.05 0.10 0.15 0.20 0.25 +Vout (V) ILoad (A) Figure 11 - +Vout vs. lLoad 12 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. -Vout vs. ILoad 5.4 5.3 5.2 5.1 -Vout (V) 85 C 5.0 25 C 4.9 - 40 C 4.8 4.7 4.6 0.00 0.05 0.10 0.15 0.20 0.25 ILoad (A) Figure 12 - -Vout vs. lLoad +Vout vs. ILoad, VS = 2.5V 2.0 1.9 1.8 1.7 25 C 85 C +Vout (V) 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.00 0.05 0.10 - 40 C 0.15 0.20 0.25 ILoad (A) Figure 13 - +Vout vs. lLoad, Vs = 2.5V 13 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. -Vout vs. ILoad, VS = 2.5V 2.0 1.9 1.8 1.7 1.6 1.5 1.4 -40 C 1.3 1.2 1.1 1.0 0.00 25 C 85 C -Vout (V) 0.05 0.10 0.15 0.20 0.25 ILoad (A) Figure 14 - -Vout vs. lLoad, Vs 2.5V Vout vs. RLoad 5.5 85 C 5.0 25 C -40 C 4.5 Vout (V) 4.0 3.5 3.0 0 10 20 30 40 50 60 70 80 90 100 110 RLoad (ohms) Figure 15 - Vout vs Rload 14 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Supply Current 16.0E-3 14.0E-3 Supply Current (A) 12.0E-3 10.0E-3 8.0E-3 6.0E-3 4.0E-3 2.0E-3 000.0E+0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 - 40 C 25 C 85 C +/- Supply (V) Figure 16 - Supply Current vs. Supply Voltage Source Current, Vo = 0V 1.4 25 C 1.2 - 40 C 1.0 Current (A) 85 C 0.8 0.6 0.4 0.2 0.0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 +/- Supply (V) Figure 17 - Sourcing Current vs. Supply Voltage 15 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Sinking Current, Vo = 0V 1.2 25 C 1.0 - 40 C 0.8 85 C Current (A) 0.6 0.4 0.2 0.0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 +/- Supply (V) Figure 18 - Sinking Current vs. Supply Voltage Vos vs. VS 140.0E- 6 120.0E- 6 100.0E- 6 85 C Vos (V) 80.0E- 6 - 40 C 60.0E- 6 25 C 40.0E- 6 20.0E- 6 000.0E+0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 +/- Supply (V) Figure 19 - Vos vs. VS 16 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Vos vs Vcm 7.0E-3 6.0E-3 5.0E-3 Vos (V) 4.0E-3 3.0E-3 2.0E-3 85 C 1.0E-3 - 40 C 0.0 1.0 2.0 3.0 4.0 25 C 5.0 6.0 000.0E+0 Vcm (V) Figure 20 - Vos vs. Vcm Vos vs. Vcm , VS = +/- 2.5V 600.0E-6 500.0E-6 400.0E-6 Vos (V) 25 C 300.0E-6 85 C 200.0E-6 -40 C 100.0E-6 000.0E+0 0.0 0.2 0.4 0.6 0.8 Vcm (V) 1.0 1.2 1.4 1.6 Figure 21 - Vos vs. Vcm, Vs = 2.5V 17 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Bias Current vs. Vsupply -4.0E- 6 -4.5E- 6 -5.0E- 6 -5.5E- 6 - 40 C Current (A) -6.0E- 6 -6.5E- 6 -7.0E- 6 -7.5E- 6 85 C -8.0E- 6 -8.5E- 6 -9.0E- 6 1.0 2.0 3.0 4.0 5.0 6.0 7.0 25 C +/- Supply (V) Figure 22 - Bias Current vs. Vsupply Offset Current vs. Vsupply 25.0E- 9 20.0E- 9 85 C Current (A) 15.0E- 9 10.0E- 9 25 C 5.0E-9 - 40 C 000.0E+0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 +/- Supply (V) Figure 23 - Offset Current vs. Vsupply 18 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harm onic Distortion vs. Load F = 1MHz, Vout = 2Vpp -60 -65 Harmonic Distortion (dBc) -70 -75 -80 -85 -90 3 r d Ha r moni c 2 nd H a r moni c -95 -100 -105 0 50 100 150 200 250 300 350 400 450 500 Load Resistance (ohm s) Figure 24 - Harmonic Distortion vs. Load F = 1MHZ, Vout = 2Vpp Harm onic Distortion vs. Load VS = +/- 2.5V, F = 1MHz, Vout = 2Vpp -60 -65 Harmonic Distortion (dBc) -70 -75 -80 -85 -90 -95 -100 -105 0 50 100 150 200 250 300 350 400 450 500 2 nd Ha r moni c 3 r d H a r moni c Load Resistance (ohm s) Figure 25 - Harmonic Distortion vs. Load Vs = 2.5V, F = 1MHz, Vout = 2Vpp 19 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harm onic Distortion vs. Output Voltage VS = +/- 2.5V, F = 1MHz - 40 Harmonic Distortion (dBc) - 50 - 60 3 r d H a r m o ni c - 70 - 80 - 90 2 n d H a r m o ni c -100 -110 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage (Vpp) Figure 26 - Harmonic Distortion vs. Output Voltage Vs = 2.5V, F = 1MHz Harm onic Distortion vs. Output Voltage F = 1MHz -40 Harmonic Distortion (dBc) -50 -60 3 r d Ha r moni c -70 -80 2 nd H a r moni c -90 -100 -110 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 Output Voltage (Vpp) Figure 27 - Harmonic Distortion vs. Output Voltage F = 1MHz 20 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harm onic Distortion vs. Output Voltage VS = +/- 2.5V, F = 1MHz, RL = 25ohm s -40 Harmonic Distortion (dBc) -50 3 r d Ha r moni c -60 -70 2 n d H a r m on i c -80 -90 -100 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage (Vpp) Figure 28 - Harmonic Distortion vs. Output Voltage Vs = 2.5V, F = 1MHz, RL = 25 Harm onic Distortion vs. Output Voltage F = 1MHz, RL = 25ohm s -40 Harmonic Distortion (dBc) -50 -60 2 n d H a r m on i c -70 3 r d Ha r moni c -80 -90 -100 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 Output Voltage (Vpp) Figure 29 - Harmonic Distortion vs. Output Voltage F = 1MHz, RL = 25 21 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harm onic Distortion vs. Output Voltage F = 10MHz -20 Harmonic Distortion (dBc) -30 3 r d H a r m on i c -40 -50 -60 2 n d H a r m on i c -70 -80 -90 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 Output Voltage (Vpp) Figure 30 - Harmonic Distortion vs. Output Voltage F = 10MHz Harm onic Distortion vs. Output Voltage F = 10MHz, RL = 25ohm s -20 Harmonic Distortion (dBc) -30 3 r d Ha r moni c -40 -50 2 nd Ha r moni c -60 -70 -80 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 Output Voltage (Vpp) Figure 31 - Harmonic Distortion vs. Output Voltage F = 10MHz, RL = 25 22 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harm onic Distortion vs. Frequency Vout = 2Vpp - 30 - 40 Harmonic Distortion (dBc) - 50 - 60 3 r d H a r moni c - 70 - 80 - 90 -100 - 110 -120 100.0E+3 1.0E+6 10.0E+6 2 nd H a r moni c Frequency (Hz) Figure 32 - Harmonic Distortion vs. Frequency Vout = 2Vpp Harm onic Distortion vs. Output Voltage VS = +/- 2.5V, F=10MHz - 30 Harmonic Distortion (dBc) - 40 3 r d Ha r moni c - 50 - 60 2 nd Ha r moni c - 70 - 80 - 90 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage (Vpp) Figure 33 - Harmonic Distortion vs. Output Voltage Vs = 2.5V, F = 10MHz 23 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harm onic Distortion vs. Frequency Vout = 2Vpp, RL = 25ohm s -30 -40 Harmonic Distortion (dBc) -50 3 r d Ha r moni c -60 -70 2 n d H a r m on i c -80 -90 -100 -110 100.0E+3 1.0E+6 10.0E+6 Frequency (Hz) Figure 34 - Harmonic Distortion vs. Frequency Vout = 2Vpp, RL = 25 Harm onic Distortion vs. Output Voltage VS = +/- 2.5V, F = 10MHz, RL = 25 ohm s -20 Harmonic Distortion (dBc) -30 3 r d H a r moni c -40 -50 2 nd H a r moni c -60 -70 -80 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage (Vpp) Figure 35 - Harmonic Distortion vs. Output Voltage Vs = 2.5V, F = 10MHz, RL = 25 24 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Harm onic Distortion vs. Frequency VS = +/- 2.5V, Vout = 2Vpp -30 -40 Harmonic Distortion (dBc) -50 -60 3 r d H a r m on i c -70 -80 -90 -100 -110 -120 100.0E+3 1.0E+6 10.0E+6 2 nd Ha r moni c Frequency (Hz) Figure 36 - Harmonic Distortion vs. Frequency Vs = 2.5V, Vout = 2Vpp Harm onic Distortion vs. Frequency VS = +/- 2.5V, Vout = 2Vpp, RL = 25ohm s - 30 - 40 Harmonic Distortion (dBc) - 50 3 r d H a r m o ni c - 60 - 70 - 80 - 90 -100 - 110 100.0E+3 1.0E+6 10.0E+6 2 nd H a r m o ni c Frequency (Hz) Figure 37 - Harmonic Distortion vs. Frequency Vs = 2.5V, Vout = 2Vpp, RL = 25 25 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Small Signal Frequency Response 25.0 G = 10 20.0 15.0 G=5 Gain (dB) 10.0 5.0 G=2 0.0 -5.0 -10.0 1.0E+3 10.0E+3 100.0E+3 1.0E+6 Frequency (Hz) 10.0E+6 100.0E+6 1.0E+9 Figure 38 - Small Signal Frequency Response Frequency Response, Vo = 200mVpp 8.0 VS = 12V 6.0 4.0 Gain (dB) 2.0 VS = 5V 0.0 -2.0 -4.0 -6.0 100.0E+3 1.0E+6 10.0E+6 Frequency (Hz) 100.0E+6 1.0E+9 Figure 39 - Frequency Response, VO = 200mVpp 26 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Pulse Response 2.5 2.0 1.5 Output Voltage (V) 1.0 0.5 0.0 -0.5 -1.0 -1.5 -2.0 -2.5 5.4E- 6 5.5E-6 5.6E-6 5.7E-6 5.8E-6 5.9E-6 6.0E-6 6.1E-6 Tim e (s) Figure 40 - Pulse Response Pulse Response, VS = +/- 2.5V 0.6 0.4 Output Voltage (V) 0.2 0.0 -0.2 -0.4 -0.6 5.4E-6 5.5E-6 5.6E-6 5.7E-6 5.8E-6 5.9E-6 6.0E-6 6.1E-6 Tim e (s) Figure 41 - Pulse Response, Vs = 2.5V 27 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. PSRR vs. Frequency 100 90 80 70 60 PSRR (dB) 50 40 30 20 10 0 10.0E+0 100.0E+0 1.0E+3 10.0E+3 Frequency (Hz) 100.0E+3 1.0E+6 10.0E+6 Figure 42 - PSRR vs Frequency CMRR vs. Frequency 90 80 70 60 CMRR (dB) 50 40 30 20 10 0 10.0E+0 100.0E+0 1.0E+3 10.0E+3 100.0E+3 1.0E+6 10.0E+6 Frequency (Hz) Figure 43 - CMRR vs. Frequency 28 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. PSRR vs. Frequency VS = +/- 2.5V 100 90 80 70 PSRR (dB) 60 50 40 30 20 10 0 10.0E+0 100.0E+0 1.0E+3 10.0E+3 100.0E+3 1.0E+6 10.0E+6 Frequency (Hz) Figure 44 - PSRR vs. Frequency Vs = 2.5V CMRR vs. Frequency VS = +/- 2.5V 90 80 70 60 50 40 30 20 10 0 10.0E+0 100.0E+0 1.0E+3 10.0E+3 100.0E+3 1.0E+6 10.0E+6 CMRR (dB) Frequency (Hz) Figure 45 - CMRR vs. Frequency Vs = 2.5V 29 Zarlink Semiconductor Inc. ZL40167 Data Sheet Typical Performance Characteristics At TA = 25C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless otherwise specified. Input Noise Voltage vs. Frequency 3.85E-09 3.80E-09 Voltage Noise (V/sqrt(Hz)) 3.75E-09 3.70E-09 VS =+ / - 2 . 5 V 3.65E-09 3.60E-09 VS =+ / - 6 V 3.55E-09 100.0E+0 1.0E+3 10.0E+3 100.0E+3 1.0E+6 10.0E+6 Frequency (Hz) Figure 46 - Noise Voltage vs. Frequency Input Current Noise vs. Frequency 4.0E-12 3.8E-12 3.6E-12 Current Noise (A/sqrt(Hz)) 3.4E-12 3.2E-12 3.0E-12 2.8E-12 2.6E-12 2.4E-12 2.2E-12 2.0E-12 100.0E+0 VS=+/-6V VS=+/-2.5V 1.0E+3 10.0E+3 100.0E+3 1.0E+6 10.0E+6 Frequency (Hz) Figure 47 - Current Noise vs. Frequency 30 Zarlink Semiconductor Inc. For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request. Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE |
Price & Availability of ZL40167DCB
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |